Short answer: PE #0.6 to #0.8 braid, a fluorocarbon leader of about 1.5 to 2.5 m in 8 to 12 lb, an FG or PR knot to join them, and a small egi snap to the jig. Drop to PE #0.4 for finesse work. Go up to PE #1.2 and a 24 lb leader for heavy kelp.
The standard eging setup
| Part | Spec | Why |
|---|---|---|
| Main line | PE #0.6 to #0.8 braid (#0.4 for finesse, #1.2 for heavy kelp) | Thin, low stretch and sensitive. It carries the sweep of the rod down to the jig and shows you the line moving on the fall. |
| Leader | 8 to 12 lb fluorocarbon, about 1.5 to 2.5 m (24 lb in heavy kelp) | Takes the abrasion from weed, reef and pier edges, and is hard for squid to see. |
| Knot | FG or PR | Slim braid-to-leader knots that pass the guides cleanly. |
| Snap | Small egi snap | Bulky hardware spoils the way the jig sits and falls. |
| Reel | 2500 or C3000 spinning, shallow spool, double handle | A shallow spool loads PE 0.6 to 0.8 with the right line lay. The double handle stops the handle swinging during the pause. |
| Drag | Smooth rather than strong. 1 to 2 kg of clean drag is plenty | A big squid pulses at the wall and you need drag that does not stutter. Maximum drag figures do not matter here. |
Why thin braid
Thin braid has little drag in wind and water, so the jig moves when the rod moves. In wind, resist the urge to go heavier. Size the jig up and keep the line thin. A heavier braid catches more wind and dulls the action.
Leader numbers and pounds
Japanese fluorocarbon is sold by number, and the pound rating differs between makers, so check each listing. On the Sunline SaltiMate Egi Leader range, #1.75 is 7 lb (3.5 kg), #2 is 8 lb (4 kg) and #2.5 is 10 lb (5 kg), while the VARIVAS Avani Eging Premium VSP lists #1.7 as 8 lb and #2 as 10 lb. The usual range for eging is 8 to 12 lb, with 24 lb kept for heavy kelp.
Marked line is worth having
Colour marking shows where the jig sinks to and where the take happened. Sunline SaltiMate PE Egista 8 is marked every 2.5 m, VARIVAS Avani Eging Max Power PE X9 has bite markers every 2 m, and Sunline SaltiMate PE EGI ULT HS8 changes colour every 10 m.
Heavy kelp and big calamari
At kelp jetties such as Flinders in Victoria, the usual set-up is PE #1.2 with a 24 lb fluorocarbon leader and 3.5 slow-sink or 4.0 jigs. The leader takes most of the abuse from kelp, so check it often.
Lines we stock for eging
- Braid: VARIVAS Avani Eging Max Power PE X9, Sunline SaltiMate PE Egista 8 and PE EGI ULT HS8.
- Fluorocarbon leader: Sunline SaltiMate Egi Leader FC, FC Hard, SV-I and Black Stream, and VARIVAS Avani Eging Premium Shock Leader VSP.
- Snap: Daiwa EG Snap Tsuyojiku Sokkou.
The full range is in Line & Leader.
Common questions
What reel size do I need for eging?
A 2500 or C3000 spinning reel with a shallow spool, ideally a double-handle model. The reels we stock are mostly built for this.
How often should I check the leader?
After every snag and every big fish. Run a fingernail along it and retie if it feels rough.
Can I use heavier braid to be safe?
Heavier braid is not safer for squid. It catches more wind and spoils the jig's action. Put the extra strength in the leader, where the abrasion is.
Building a whole outfit? Start with the eging guide or ask us.



Leave a comment
This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.